RigPlan
Wall in. Truck list out.
FREE BETA · SPECS FROM DATASHEETS

LED wall calculator and pack list generator

The free LED wall calculator that goes past pixels and power: describe the wall once and RigPlan derives the full pack list — panels and spares, rigging hardware from your own bumper stock, circuits and distro, data runs and processor fit, cases and truck space — so nothing gets remembered at midnight or forgotten at load-in.

Job

Venue limits
What the venue and logistics actually offer — the job warns when the design exceeds them.

Walls

+ wall 🔒

Planning several walls on one job — main + IMAG + DJ riser, shared spares and one truck sum — is a Solo feature.

Specs from ROE Visual — Black Pearl specifications. Hanging limit valid with ROE hanging bars, indoor, safety factor 5.
Your panels · add custom spec

Datasheet PDF parsing — upload a sheet, get the form pre-filled — is a Solo feature. Manufacturers can always parse and submit sheets free on the vendors page.

Saved in this browser only for now — accounts will sync them. Specs offered to the public database are reviewed by hand before publishing; leave the box unticked to keep a spec fully private.
8.00 × 4.50 m · 2,816 × 1,584 px · 16:9

Quick resolution · size + pitch

2,069 × 1,034 px · 2.14 M px · 5× 1G @ 80%
Rough check before you know the panel. Assumes ~650 k px per 1G port at 60 Hz 8-bit, loaded to your port limit.

Rig stock · bumpers

What your shop owns — shared across every wall in the job, allocated in wall order. Shortfalls land on the wall that runs out. Used when flown. Saved in this browser. Assumes every rig hangs on the same bars — if your bars are system-specific, the Solo and Shop tiers track bars per panel system.
Pack list · 1 wall · 60 Hz 8-bit · Main 16×9
Walls
1
Main
Panels
144+8
wall + spares, all walls
Weight
1,546 kg
all walls incl. bumpers
Power
23 kW
max · ~11.5 kW typical · 8× circuits
Data
16 runs
2 processors · 60 Hz 8-bit
Truck
6 m
linear deck estimate

Pack list

0/22 packed

Panels0/4 packed

144 pcsROE Black Pearl BP2 V2 tiles16×9 wall, 8.0×4.5 m
8 pcsSpare tilesone-off rate 5%
6 pcsSpare receiving cards
6 pcsSpare PSUs

Rigging0/6 packed

8 pcs2-wide bumpersfrom your stock
3 pcsChain hoists, 1 tpoint load ~619 kg incl. 1.2 dyn.
6 pcsSteels, 1 m2 per point
6 pcsSpansets2 per point
12 pcsShackles, 3.25 t4 per point
9 mTruss to span wall+1 m overhang — or house points

Power0/3 packed

1 pcs63 A 3-phase distro23 kW max · ~11.5 kW typical content
8 pcsFeeder lines to wall (16 A / 230 V)~30 m each
150 pcsTRUE1 jumperspanel-to-panel, incl. 10% spare

Data & control0/3 packed

2 pcsNovastar VX100016/20 ports used
16 pcsCat6A home runs, ~40 mrun + height + 5 m loop
159 pcsCat6 panel jumpersincl. 10% spare

Cases & truck0/6 packed

19 pcsPanel dollies8 tiles per dolly
1 pcsBumper cases8 per case
6 pcsCable trunks~333 cables total
1 pcsRigging trunks
1 setGaff, velcro, zip ties, sharpiesalways
6 mTruck deck, linear29 cases est.

Data wiring16 runs · ≤16 panels/run @ 80% · worst 43% · 2× Novastar VX1000

R143%R243%R343%R443%R543%R643%R743%R843%R943%R1043%R1143%R1243%R1343%R1443%R1543%R1643%2w2w2w2w2w2w2w2w~619 kg~619 kg~619 kg8.00 m · 2,816 px4.50 m · 1,584 px23 kW max · 8× 16 A / 230 V · 16 runs → 2× Novastar VX1000
Run 1Column 19 panels · 43% of port
Run 2Column 29 panels · 43% of port
Run 3Column 39 panels · 43% of port
Run 4Column 49 panels · 43% of port
Run 5Column 59 panels · 43% of port
Run 6Column 69 panels · 43% of port
Run 7Column 79 panels · 43% of port
Run 8Column 89 panels · 43% of port
Run 9Column 99 panels · 43% of port
Run 10Column 109 panels · 43% of port
Run 11Column 119 panels · 43% of port
Run 12Column 129 panels · 43% of port
Run 13Column 139 panels · 43% of port
Run 14Column 149 panels · 43% of port
Run 15Column 159 panels · 43% of port
Run 16Column 169 panels · 43% of port

Power runs8 circuits · ≤18 panels/circuit · 23 kW max · 1× distro

C1 ⇅L1C2 ⇅L2C3 ⇅L3C4 ⇅L1C5 ⇅L2C6 ⇅L3C7 ⇅L1C8 ⇅L22w2w2w2w2w2w2w2w~619 kg~619 kg~619 kg8.00 m · 2,816 px4.50 m · 1,584 px23 kW max · 8× 16 A / 230 V strings · phases L1–L3 suggested
Circuit 1Columns 1–2 · snake up/down, hops right18 panels · 2,880 W · 98% · Distro 1 · L1
Circuit 2Columns 3–4 · snake up/down, hops right18 panels · 2,880 W · 98% · Distro 1 · L2
Circuit 3Columns 5–6 · snake up/down, hops right18 panels · 2,880 W · 98% · Distro 1 · L3
Circuit 4Columns 7–8 · snake up/down, hops right18 panels · 2,880 W · 98% · Distro 1 · L1
Circuit 5Columns 9–10 · snake up/down, hops right18 panels · 2,880 W · 98% · Distro 1 · L2
Circuit 6Columns 11–12 · snake up/down, hops right18 panels · 2,880 W · 98% · Distro 1 · L3
Circuit 7Columns 13–14 · snake up/down, hops right18 panels · 2,880 W · 98% · Distro 1 · L1
Circuit 8Columns 15–16 · snake up/down, hops right18 panels · 2,880 W · 98% · Distro 1 · L2
PatchDistro 1: circuits 1–8 (L1×3 L2×3 L3×2)
Made with RigPlan — the free LED wall planner · rigplan.app

The rules behind every number

Every quantity above is derived from the rules below — written with working AV techs and corrected as they red-pen them. Panel and processor specs are placeholders until verified against manufacturer data.

  1. openSpare panels: 5% of wall count, minimum 2 (one-off).
  2. ✓ confirmedBumpers come from your stock, not a formula: widest first, combined to cover 16 columns. Partial coverage (a wider bar over fewer columns) is allowed and noted; shortfalls are flagged instead of invented.
  3. openBumper weights 35/25/15 kg for 3/2/1-wide — placeholder.
  4. openRigging points: one per ≤3 m of wall width, minimum 2 → 3. 1× 1 t hoist per point.
  5. openPer point: 2× steel, 2× spanset, 4× 3.25 t shackle.
  6. openPoint load: wall weight ÷ points × 1.2 dynamic factor. Warn above 800 kg per 1 t hoist.
  7. ✓ confirmedCircuits sized on max load (full white) at 80% derate: 18 panels per 16 A / 230 V circuit (160 W/panel). Typical draw shown separately for the venue/generator ask.
  8. ✓ confirmedPower runs follow the connectors: in one side, out the other, gendered plugs, jumpers as short as the maker can get away with. Vertical works both ways, sideways only one hop to the right (rear view) — so a run may snake up and down across adjacent columns, but never left and right. Vertical snakes over 2 columns → 8 circuits (single columns would need 16, full rows 9).
  9. open1× 63 A 3-phase distro per 18 circuits (1). TRUE1 jumpers = panels − runs, +10% spare.
  10. ✓ confirmedRuns are load-balanced: panels split evenly across the circuits a shape needs — 12+12, never 18+6 — so every main-in pulls about the same. Phases are a suggested round-robin L1–L3 within each distro.
  11. ✓ confirmedExact-pixel mapping (Novastar VX1000): a port carries only the panels wired to it, and data snakes in any direction (unlike power). Wiring follows whole columns as vertical serpentines, numbered from the left seen from the rear — the natural reading order when patching — with every run capped at 80% of 650 k px per 1G port at 60 Hz 8-bit (threshold, refresh and depth adjustable): ≤16 panels per run → 16 runs, worst run 43%. Loads balance evenly across runs. Capacity scaling is theoretical bandwidth (60/Hz × 24/bpp), and per-port width caps on modern controllers are not modelled yet — correct me with measured figures.
  12. ✓ confirmedRedundancy defaults off — rental shows rarely run looped data; it's primarily a critical-installation feature. Turning it on doubles the runs (A+B loops).
  13. openHome runs cut at run distance + wall height + 5 m service loop.
  14. openProcessors are checked on two limits: port count and total pixel capacity (capacities placeholder).
  15. ✓ confirmedProcessor list defaults to Novastar (VX1000 first, UHD Jr / MCTRL / MX / VX family) — rental houses rarely run Brompton; it stays available for the shops that do. All figures verified against manufacturer spec sheets.
  16. openCases: 8 panels per dolly, 60 cables per trunk, 8 bumpers per case, rigging trunk per 6 points. Truck estimate: 0.5 m² footprint per case over 2.4 m trailer width.
  17. openElectronics spares: 1 receiving card per 25 panels, 1 PSU per 25, minimum 1 each.

LED wall calculations, answered

How do I calculate LED wall resolution?

Multiply the panel count by the pixels per cabinet: a 12 × 6 wall of 176 × 176 pixel cabinets is 2,112 × 1,056 pixels. From physical size instead, divide width and height in millimetres by the pixel pitch — a 6 m wide wall at 2.9 mm pitch is about 2,069 pixels wide.

How much power does an LED wall need?

Multiply panel count by the maximum (full white) draw for circuit sizing, and apply an 80% derate to the circuit rating. A 16 A/230 V circuit carries 2,944 usable watts, so sixteen 180 W panels. Typical content draws roughly a third of maximum — use that figure for generator sizing, not for circuits.

How many LED panels fit on one data port?

A 1G port carries roughly 650,000 pixels at 60 Hz and 8-bit (NovaStar’s official rating; Brompton rates 525,000). Divide by the pixels per cabinet and load to about 80% for headroom. Higher refresh rates and deeper bit depths reduce the figure proportionally.

What does an LED wall pack list include?

Panels and spares, receiving cards and PSUs, bumpers and rigging hardware, hoists, power distros, feeders and jumpers, data home runs and panel jumpers, processing, dollies, cable trunks and truck space. RigPlan derives every quantity from the wall specification and the stock you own.

Is RigPlan free?

The calculator and the derived pack list are free with no sign-up. Paid plans add saved jobs, shop inventory synced across devices, branded printouts and team check-off.

More depth in the planning guides: how to calculate led wall power, how many led panels per data port, what to pack for an led wall load-in.

Calculators by panel

Each panel page opens this calculator preloaded with that tile's specification, with a worked example wall: